Product type: Basic Digital Input Kit | Range: Modicon STB | Inputs: 16 DI, 24 V DC, positive logic (sink) | Connection: spring clamp | Kit: module + base + 18-terminal connector
The STBDDI3725KC is a basic digital input kit of the Modicon STB distributed I/O range. It is supplied complete: the STBDDI3725 input module, the STBXBA3000 I/O base and the STBXTS2180 18-terminal spring clamp connector. The module carries 16 discrete inputs at a nominal 24 V DC with positive logic, so it sinks current from the sensor and is wired for NPN type sensors. As a basic module it comes with the factory-set default configuration and needs no configuration software: it is plugged onto the base, the island is given a network interface module, and the inputs are available to the fieldbus master.
The 16 channels are split over two 18-terminal spring clamp connectors, IN1 to IN8 on the left block and IN9 to IN16 on the right block, so field wiring can be removed block by block without touching the module. Inputs accept 2-wire or 3-wire sensors. In the 3-wire arrangement the sensor supply is taken from the connector itself: the pins alternate between sensor supply group (+) and input, and pin 9 and pin 18 carry the sensor supply negative (PDM-) for the 3-wire sensors. There are four sensor supply groups in total, two per connector block. Sensor supply is fed by the power distribution module of the island, STBPDT3100 or STBPDT3105, and the module is used on the I/O base STBXBA3000.
The input voltage range is 11 to 30 V in category 1 of IEC 61131-2, with the state 0 range at −3 to 5 V. Each channel draws 4.5 mA at 24 V DC. A state 1 is guaranteed between 15 and 30 V at 2.5 mA or more, a state 0 is guaranteed between −3 and 5 V at 1.5 mA or less. The input filter is 1 ms, response time is 2 ms from off to on and 2 ms from on to off. Inputs are protected by a resistor-limited input circuit and by reverse polarity protection. The module draws 100 mA at 5 V DC from the logic bus.
Status is visible on the front panel: one green RDY LED for the module state and one green LED per channel for the input state, IN1 to IN16. The module is 125 mm high, 28.1 mm wide and 65.1 mm deep, and it takes 28.1 mm of width on the 35 mm DIN rail once clipped on the base, so 16 input points occupy less width than two 8-channel slices. Net weight is 0.086 kg.
Operating temperature is −25 to 70 °C without derating and storage temperature −40 to 85 °C without derating, relative humidity 95 % at 60 °C without condensation, operating altitude up to 2000 m and pollution degree 2. Vibration resistance is 3 gn and 5 gn from 58 to 150 Hz on the 35 mm DIN rail with 3.5 mm amplitude from 10 to 58 Hz, and shock resistance is 30 gn for 11 ms. Protection degree is IP20. The kit is marked CE and certified FM Class 1 Division 2, UL and CSA, and conforms to IEC 61131-2 type 3. One kit is packed in a 13 x 8 x 3.5 cm carton of 194 g, and the contractual warranty is 18 months.
Note on the reference. This is the kit reference STBDDI3725KC: it includes the mounting base and a spring clamp connector. The bare module STBDDI3725 is a different reference, it is delivered without base and without connector, and its connection is a screw terminal. Buyers who need screw terminals should not order this kit expecting them.
| Characteristic | Value |
|---|---|
| Range of product | Modicon STB distributed I/O solution |
| Product or component type | Basic digital input kit |
| Kit composition | STBDDI3725 module, STBXBA3000 I/O base, STBXTS2180 18-terminal spring clamp connector |
| Product compatibility | I/O base STBXBA3000; power distribution module STBPDT3100 / STBPDT3105 |
| Discrete input number | 16 |
| Discrete input voltage | 24 V DC nominal; 11...30 V (IEC 61131-2 category 1); −3...5 V state 0 |
| Discrete input logic | Positive logic (sink) |
| Discrete input current | 4.5 mA at 24 V DC |
| Voltage state 1 | 15...30 V |
| Voltage state 0 | −3...5 V |
| Current state 1 | >= 2.5 mA |
| Current state 0 | <= 1.5 mA |
| Input filter | 1 ms |
| Response time | 2 ms off to on, 2 ms on to off |
| Input protection | Resistor-limited input, reverse polarity protection |
| Sensor supply | 4 groups, fed by the power distribution module; PDM− on pin 9 and pin 18 |
| Wiring mode | 2-wire or 3-wire sensors |
| Electrical connection | 2 x 18-terminal spring clamp connector: IN1-IN8 left, IN9-IN16 right |
| Supply type | Power distribution module (island PDM) |
| Current consumption | 100 mA at 5 V DC, logic bus |
| Local signalling | 1 RDY LED (green), 1 LED per channel (green) |
| Module type | Basic, factory-set configuration |
| Mounting | 35 mm DIN rail, on I/O base STBXBA3000 |
| Height | 125 mm |
| Width | 28.1 mm |
| Depth | 65.1 mm |
| Net weight | 0.086 kg |
| IP degree of protection | IP20 |
| Ambient air temperature for operation | −25...70 °C without derating |
| Ambient air temperature for storage | −40...85 °C without derating |
| Relative humidity | 95 % at 60 °C without condensation |
| Operating altitude | Up to 2000 m |
| Pollution degree | 2 |
| Vibration resistance | 3 gn and 5 gn, 58...150 Hz on 35 mm DIN rail; 3.5 mm, 10...58 Hz |
| Shock resistance | 30 gn, 11 ms |
| Marking | CE |
| Product certifications | FM Class 1 Division 2, UL, CSA |
| Standards | IEC 61131-2 type 3 |
| Packing unit weight | 194 g |
| Packing unit dimensions | 13 x 8 x 3.5 cm |
| Warranty | 18 months |