{"title":"Schneider Modicon TM3","description":null,"products":[{"product_id":"schneider-tm3di32k-plc-digital-input-module-32-channel-24vdc-sink-source","title":"Schneider TM3DI32K PLC Digital Input Module 32 Channel 24VDC Sink Source","description":"\u003cp\u003e32-Channel Digital Input Module for Modicon TM3, 24 VDC, HE10 Connector\u003c\/p\u003e\n\u003cp\u003eThe TM3DI32K adds 32 discrete inputs to Modicon M221, M241, M251 and M262 logic controllers. Each channel reads 24 VDC signals from sensors, limit switches, pushbuttons and relay contacts, and accepts either sink or source wiring without changing hardware, so positive and negative logic panels can share the same spare part.\u003c\/p\u003e\n\u003cp\u003eThe 32 inputs are split into two groups of 16, each group with one common line on two pins. Inputs draw 5 mA at 24 V with a 4.4 kOhm impedance and switch in 4 ms; the guaranteed thresholds are 15 V for ON and 5 V for OFF, and the input type meets IEC\/EN 61131-2 Type 1. 500 VAC isolation separates the inputs from the internal logic, and every channel has its own green status LED on the front.\u003c\/p\u003e\n\u003cp\u003eWiring uses a removable HE10 (MIL 20) ribbon connector rather than screw terminals, which keeps a 32-channel block down to 33.5 mm of DIN rail width and speeds up replacement. Unshielded cable runs up to 30 m are supported, the connector is rated for more than 100 insertion cycles, and the module is powered from the TM3 bus so no separate supply is needed for the logic side.\u003c\/p\u003e\n\u003cp\u003eKey features\u003cbr\u003e- 32 discrete inputs, 24 VDC, IEC\/EN 61131-2 Type 1\u003cbr\u003e- Sink or source wiring, configurable without hardware change\u003cbr\u003e- 2 groups of 16 inputs, 1 common line each\u003cbr\u003e- 5 mA input current, 4.4 kOhm impedance\u003cbr\u003e- ON from 15 V, OFF up to 5 V\u003cbr\u003e- 4 ms turn-on \/ 4 ms turn-off\u003cbr\u003e- 500 VAC isolation between inputs and internal logic\u003cbr\u003e- Removable HE10 (MIL 20) connector, 100+ mating cycles\u003cbr\u003e- Unshielded cable up to 30 m\u003cbr\u003e- 32 green channel LEDs\u003cbr\u003e- 33.5 mm wide on 35 mm DIN rail\u003c\/p\u003e\n\u003cp\u003eSpecifications\u003cbr\u003eProduct type: Discrete input module\u003cbr\u003eRange: Modicon TM3\u003cbr\u003eCompatibility: Modicon M221, M241, M251, M262\u003cbr\u003eInput channels: 32\u003cbr\u003eInput groups: 2 x 16, one common line per group\u003cbr\u003eInput type: Type 1 per IEC\/EN 61131-2\u003cbr\u003eInput logic: Sink or source\u003cbr\u003eRated input voltage: 24 VDC (19.2-28.8 V)\u003cbr\u003eRated input current: 5 mA\u003cbr\u003eInput impedance: 4.4 kOhm\u003cbr\u003eState 1: \u0026gt; 15 VDC, \u0026gt;= 2.5 mA\u003cbr\u003eState 0: 0-5 VDC, \u0026lt;= 1 mA\u003cbr\u003eResponse time: 4 ms on, 4 ms off\u003cbr\u003eIsolation: 500 VAC input to internal logic\u003cbr\u003eConnection: HE10 (MIL 20) connector\u003cbr\u003eMaximum cable length: 30 m unshielded\u003cbr\u003eCurrent consumption: 46 mA at 5 VDC bus, all inputs on; 5 mA all off\u003cbr\u003eLocal signalling: 1 green LED per channel\u003cbr\u003eMounting: 35 mm DIN rail (TH35-7.5 \/ TH35-15) or panel\u003cbr\u003eProtection: IP20\u003cbr\u003eAmbient temperature: -10 to 55 C (horizontal installation)\u003cbr\u003eDimensions: 90 x 33.5 x 81.3 mm (H x W x D)\u003cbr\u003eNet weight: 0.1 kg\u003cbr\u003e\u003c\/p\u003e","brand":"Schneider Electric","offers":[{"title":"Default Title","offer_id":68124463923288,"sku":null,"price":93.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0580\/2799\/9320\/files\/TM3DI32K......jpg?v=1794045425"},{"product_id":"schneider-tm3dq32uk-plc-transistor-output-module-32-channel-24vdc-sink-npn","title":"Schneider TM3DQ32UK PLC Transistor Output Module 32 Channel 24VDC Sink NPN","description":"\u003cp\u003e32-Channel Transistor Output Module for Modicon TM3, 24 VDC Sink (NPN)\u003c\/p\u003e\n\u003cp\u003eThe TM3DQ32UK adds 32 transistor outputs to Modicon M221, M241, M251 and M262 logic controllers. Outputs are negative logic (sink \/ NPN), so each channel switches the 0 V side of the load and the field device stays connected to +24 V. Solid-state switching gives a 450 µs response with no contact wear, which suits solenoid valves, indicators and high-cycle pneumatic actuators better than relay outputs.\u003c\/p\u003e\n\u003cp\u003eThe 32 outputs are split into two groups of 16, each group with one common line on two pins. Each channel carries 0.1 A and each common line carries 2 A, so the module is built for dense signal-level loads rather than direct motor or heater switching. Leakage current in the OFF state is 0.1 mA maximum and voltage drop is below 0.4 V. A clamping voltage of about 50 VDC handles the reverse pulse from inductive loads, and the outputs are protected against reverse polarity.\u003c\/p\u003e\n\u003cp\u003eTwo limits need attention at commissioning. The module has no internal short-circuit protection, so a fast external fuse is required for each group. The outputs are not isolated from one another, only 500 VAC from the internal logic, so all 32 channels must reference the same supply. Wiring uses a removable HE10 (MIL 20) connector, keeping 32 channels in 33.5 mm of DIN rail width, with unshielded cable runs up to 5 m.\u003c\/p\u003e\n\u003cp\u003eKey features\u003cbr\u003e- 32 transistor outputs, 24 VDC, sink (NPN \/ negative logic)\u003cbr\u003e- 2 groups of 16 outputs, 1 common line each\u003cbr\u003e- 0.1 A per channel, 2 A per common line\u003cbr\u003e- Response time 450 µs on \/ 450 µs off\u003cbr\u003e- No contact wear, unlimited switching cycles\u003cbr\u003e- Leakage 0.1 mA max, voltage drop below 0.4 V\u003cbr\u003e- Reverse polarity protection, 50 VDC clamping\u003cbr\u003e- 500 VAC isolation between outputs and internal logic\u003cbr\u003e- Removable HE10 (MIL 20) connector\u003cbr\u003e- Unshielded cable up to 5 m\u003cbr\u003e- 32 green channel LEDs\u003cbr\u003e- 33.5 mm wide on 35 mm DIN rail\u003c\/p\u003e\n\u003cp\u003eSpecifications\u003cbr\u003eProduct type: Discrete output module\u003cbr\u003eOutput type: Transistor\u003cbr\u003eRange: Modicon TM3\u003cbr\u003eCompatibility: Modicon M221, M241, M251, M262\u003cbr\u003eOutput channels: 32\u003cbr\u003eOutput groups: 2 x 16, one common line per group\u003cbr\u003eOutput logic: Sink (NPN, negative logic)\u003cbr\u003eRated output voltage: 24 VDC (19.2-28.8 V)\u003cbr\u003eRated output current: 0.1 A per channel\u003cbr\u003eTotal current per common: 2 A\u003cbr\u003eVoltage drop: 0.4 V max\u003cbr\u003eLeakage current OFF: 0.1 mA max\u003cbr\u003eResponse time: 450 us on, 450 us off\u003cbr\u003eSwitching frequency: 100 Hz max, resistive load\u003cbr\u003eInductive load: L\/R = 10 ms\u003cbr\u003eClamping voltage: 50 VDC typical\u003cbr\u003eReverse polarity protection: Yes\u003cbr\u003eShort-circuit protection: No, fast external fuse required\u003cbr\u003eIsolation: 500 VAC output to internal logic, none between outputs\u003cbr\u003eConnection: HE10 (MIL 20) connector, 100+ mating cycles\u003cbr\u003eMaximum cable length: 5 m unshielded\u003cbr\u003eCurrent consumption: 27 mA at 5 VDC, 31 mA at 24 VDC, all outputs on\u003cbr\u003eLocal signalling: 1 green LED per channel\u003cbr\u003eMounting: 35 mm DIN rail (TH35-7.5 \/ TH35-15) or panel\u003cbr\u003eProtection: IP20\u003cbr\u003eAmbient temperature: -10 to 55 C (horizontal), -10 to 35 C (vertical)\u003cbr\u003eDimensions: 90 x 33.5 x 81.3 mm (H x W x D)\u003cbr\u003eNet weight: 0.112 kg\u003cbr\u003e\u003c\/p\u003e","brand":"Schneider Electric","offers":[{"title":"Default Title","offer_id":68124587425880,"sku":null,"price":65.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0580\/2799\/9320\/files\/TM3DQ32UK......jpg?v=1794048726"}],"url":"https:\/\/gexufein.com\/collections\/schneider-modicon-tm3.oembed","provider":"Gexufein Automation","version":"1.0","type":"link"}